Whether you use a bow and arrows for recreation or hunting, keeping it is essential for an effective shot every time. But buying the parts can be expensive, and it can feel like an achievement in itself of using your own materials.
That is why the purpose of this article is to teach you how to make an arc rope with elements that you already have around your house. There are a variety of methods that have been used to make bowstrings, as well as a variety of materials, so you can adapt what you have around to create a versatile bowstring for when you need it.
How to make a flamenco-style bow rope.
This is one of the simplest methods to make a bowstring, but it does require some additional tools that you will need to obtain.
One of the most important things you will need is a template to make ropes. You can choose to buy one in the store or, if you have enough skill, you can make one yourself. To make yours, you will need the following materials:
- a pine board 1 and # 215; 6 of at least 28 inches long.
- 2 dozens of 1-inch-long finishing nails
- 1 10 penny common nail
Draw a line in the center of your board. At one end, 2 inches from the end of the board, begin to make a dotted line on each side of the center to locate the nails. Each row should be 1.25 inches away from the center. Draw each point at least .375 inches away from each other.
At the other end of the board there should be two nails aligned with the rows at the other end, again 2 inches from the end of the board and 1.25 inches from the center. Using a 5/32 inch drill bit, drill 16 holes along the middle line of the board, starting with one between the two nails.
The holes must be separated by at least one inch from each other. These are for your 10 cents nail to be used as an adjustable peg. Starting at the fourth hole, write y # 8220; 48 and # 8221; and then add increments of two to each hole (50, 52, 54, 56, etc.). These numbers correspond to the length of your bow, so you will know how much rope you should use.
Now that your template has been made, it’s time to learn how to actually make your chain. It may be a good idea to also use a pencil or marker on your template to draw a path by winding the string so you do not forget.
Starting with your row of ropes on the right side of the board, you will want to tie the end around the nail closest to the side that is away from you, draw the rope towards you and then around the last nail. Bring the string to the nail at the left end of the board, then around its pin, then around the other nail and back to the first row of nails.
But instead of wrapping the last nail, you will pass between the last and the second to the last nail. Each time you complete a row, you will decrease the amount of nails around which you are wrapping your thread. This is an easy way to know how many times you have wrapped your chain around the template.
When making your actual bow chain, it is a good idea to have two different colors so you can keep track of what you are doing. The materials you will need are:
- Dacron B-50 bowstring or fast-flying rope
- A wax cake or beeswax
- Monofilament or nylon reel for serving.
The next step is to decide if you want to make a chain of two or three layers. In regard to a double layer, they are made of two bundles of twisted yarns, while the three plays are made of three sets. This process involves the two-layer method.
The amount of strands you will need will depend on the range of your bow’s weight. For example:
- For the range of 40 to 50 pounds, you will need 12 strands;
- for 50-70, you will need 14 strands;
- For 70-80, you will need 18 strands.
For a two-game chain, you would need two groups of six chains each, while a three-chain group would require three groups of four chains each. Practice and repeat the above mentioned method until you have 6 threads in the template. Then, cut the strands with a sharp knife through the center line between the upper nails.
Carefully remove the string from the template and make sure the ends do not move. The ends of each strand should be shorter than the previous one. Doing this helps each strand lock in place while you make the bowstrings. Leave this aside for the moment and repeat the process with a different color.
Wax both ends of each pack, up to about ten inches. Heating the wax would be a good idea to adhere to the ropes much better. Then, place the packages side by side so that the longest strand of each package is aligned with each other.
Using a ruler, take the packages approximately 7 inches away from the ends between the thumbs and indexes and rotate them six to seven times in a counterclockwise motion. Take your twisted package and rotate it over the top of the lower package (toward you); That will make the lower package at the top. Repeat the torsion and rotation process until all the strands have been incorporated into the bowstring. Once you have finished, form the top end of your bow and it should be wide enough to slide down at least five to six inches when not tied.
Now is the time to place your bowstring on the ground. Form your twisted bundle into a loop, with a colored string on the left and the other on the right. Grasp the bottom of the loop and rotate the two beams of the same color on each side.
Now keep these two packages together and perform the same rotation and rotation procedure as before until the last end has been twisted in the rope. Once this is done, separate both packages to the bottom. Then, using the same 7-inch measure, repeat the entire process at the other end of the bowstring. While you braid and create the lower loop, you must keep the rest of the strands separated along the length of the string.
If you do not want to create a permanent loop, you can choose to braid at least 8 to 10 inches from the lower beams and then tie a wooden hook to the loop to make it adjustable.
Once completed, you must place a twist on the bowstring. The turn must be in the same direction as the braids, or you’ll end up unscrewing all the loops you’ve made. Once this is done, place the rope in your bow and adjust it to the correct height of the clamp. Leave your bow for one or two days and allow yourself to get used to the new rope that has placed you. Take some pictures with your bow to make sure everything is working properly. Remember to adjust the height of the clamp by twisting and unscrewing the rope regularly until all the stretch has been resolved.
On the string, mark where you think the nocking point will be, and mark two inches above this point and six inches below. In this area is where the monofilament will be served to provide more strength to the bowstring. Place the spool on the service tool and take out a few inches of your line. Adjust the tension of your service tool so that it has a tight wrapping around the bowstring. Using too much tension can end up cutting the bowstring, so it’s important to fight against the correct level.
Separate the bowstring at each end of the service area and insert 1 inch of monofilament through the rope. Begin to roll it around the bowstring while the loose end is held under the wrapper to serve; you must continue to wrap it until it is 1/4 inch from the end of the service area.
Now is the time to use your B-50 chain. Cut around a cord of 10 to 12 inches and form a loop at one end. Place it on the bowstring with the loop towards the end of the limb and then wrap the monofilament over this string at least 6 to 8 times more; these should be kept loose
Add a few more inches of monofilament once you are at the end of the service area and cut the line. Insert the end through the loop of the B-50 chain, and pull the ends under the last turns of monofilament. Then give him a good hair removal session; Use a piece of old leather to do the work. You will have to rub the wax hard and fast to melt it and make sure it is between all the ropes.
If the previous instructions were a bit difficult to follow, here is a useful video that details the entire process. However, the template is already pre-made but it gives you an idea of how it should be, if you choose to do it yourself:
a video that shows how to make a flamenco string without using a template to make strings.
How to make a bowstring for a crossbow.
Crossbows are a bit different from regular bows and require a slightly different type of chain. But that does not mean you can not spend your time doing yours.
The string template you will need is very different from the one mentioned above. When doing yours, all you need is a piece of table of 2 and n. ° 215; 6, and a 10 inch and a half inch bolt with the top cut off. Simply attach them to the wood; the distance between them must be the desired length of the finished chain. You will also need a service template to attach a string where your arrow is notched. Finally, you will need a bit of rope; B-50 does the trick and must form the main part of the string, and the monofilament can be used for the central portions.
First, you must reserve 18 inches of bowstring and, using one end of the service wire, tie a known grandmother around the chain in which you want to start the service. A few centimeters should be left at the free end. Place this end along the chain where you want to place the portion. Using the service template, wrap the first inch over the end of the string and continue serving until it reaches an inch where you want the portion to end.
Using the 18 and # 8243; from the previous chain, place a loop so that the end is beyond the service area. Serve over the top of the loop and make your wrappers a little looser than their previous wrappers. Finish the portion with half hook, leaving approximately three to four inches free. Using the loop to pull the end of the service wire under the wraps, and time the free ends of the material about 1/4 and # 8243; Of the portion. Burn the tips down with a lighter to finish them. Once melted, moisten the melted plastic with your wet finger or with a damp sponge.
Now that it’s done, tie a short loop at the end of your string material and temporarily attach it to one of the pins. Place 20 turns around the pins and make sure they are not too tight. Tie the end of the rope to the loop you made earlier and throw it away.
Serve 5 inches of half the strands in the center of the two pegs, then extend the ropes, using a piece of wood or a diamond braid. Turn the string until the portions are centered on one of the pins. Mark the location with tape and then rotate it again until its end is in the center of its pins. Turn back when finished.
Place the finished end of the portion so that the free end is 1/4 inch shorter than the other side. Squeeze the ends together and serve the first end. Four to five inches of serving should be enough for this. Then pinch the other end and serve that. Then it serves 6 inches to the center. Add a lot of wax to the rope so that the threads come together.
These methods require a lot of practice, so do not be discouraged if you do not do it on your first try. Once you have climbed down the steps, you will be making your own bowstring like a pro in a short time, and you will not have to bother looking through the various bow strings of the store to find what you are looking for.
There is also some satisfaction in taking care of your bow on your own and making sure it works properly without having to spend money for a new chain. If you are committed to being more self-sufficient in maintaining your bow, then you should definitely try to make your own bow chain.
DO IT YOURSELF