Tops for the feeder: what you need to know for the right choice?

Tops for the feeder are a bite alarm. However, even experienced fishermen find it difficult to select and use them. A considerable problem is the selection of an element that is suitable in diameter to the rod. Because it is important to know how to choose the right done or to make them yourself.

  • Purpose vershinok
  • 2Main Versions Characteristics
    • 2.1 Sensitivity
    • 2.2 Stiffness
    • 2.3 Length
    • 2.4Diameter
    • 2.5 Passing rings
  • 3 Versions of vershinok on production material
    • 3.1 Glass reinforced plastic
    • 3.2 Carbon
  • 4 Selection Criteria
  • 5 Trying to do it yourself
    • 5.1 Pendulum-type device
    • 5.2Kivkovogo type product
  • 6 General recommendations for use

Purpose vershinok

The top is a replaceable addition to the rod. Its main purpose is signaling bite. Such a detail is extremely important when several rods are used on fishing at the same time.

It is extremely difficult to break a quality tip on a bend. However, it is easily damaged by a fracture. In the process of fishing, she experiences loads from the weight of the feeder, as well as the strength of the current. An overly soft construction can bend too much, and a stiff one will stand straight all the time. In both cases, an incorrectly picked tip in the process of fishing will prevent catching the catch.

The main characteristics of vershinok

Despite the simplicity of the design, done to have a large number of characteristics. The main ones are:

  • The sensitivity of the design;
  • Device stiffness;
  • The length of the tip;
  • The diameter of the base.

Also, products are often classified according to the principle of their signaling:

  • Swingtip. When poklevke design begins to swing;
  • Quivertip During biting, the device trembles;
  • Sidetype, or “Side nod.” The element is located at the handle of a fishing rod.

Tops for feederOften the rod is classified precisely according to the principle of signaling the tips installed on it.

All finished devices, according to the principle of their installation, are divided into twisted, and those that need to be inserted.

Sensitivity

Most often, when buying a rod, complete with it is a set of 2-5 vershinok, differing from each other in the degree of sensitivity and rigidity. For well-known manufacturers, sensitivity is necessarily indicated on each product in ounces (oz) and is determined by dough. At the same time 1 English ounce corresponds to 28 g of the weight applied on it subsequently.

Soft sensitive designs have a range of markings of 0.5-0.7 oz. Products with medium sensitivity and stiffness are labeled within 1.5-3 oz. The least sensitive and most hard tops, which are used for fishing in difficult weather conditions or when catching trophy specimens of fish, are labeled 4-6 oz.

Rigidity

Often, manufacturers indicate the rigidity of the detector by coloring the tip of the upper part of the tip in a specific color:

  • The softest models are usually marked with green;
  • Yellow or white indicates medium hardness;
  • Red painted the toughest done.

Tops for feederThe rigidity and sensitivity parameters of products for feeder fishing are usually interrelated.

Length

Not only rigidity and sensitivity, but also the strength of the product depends on this parameter of the detector. Too short or long jigs do not react to the bite properly. In addition, they often break during operation.

The optimal length of the detector for the feeder rod is in the range of 55-75 cm. At the same time, done with a small diameter and a length of 70-75 cm are the softest, and products with a large diameter and size of 55-60 cm belong to rigid structures.

Diameter

The bore diameter of the structure plays a very important role. He must clearly fit the hole in the rod. Too large diameter will not allow to fasten the tip in the fishing rod, and a small one will lead to unreliable fastening. Top will simply fall out. Of course, if desired, unsuitable in size products can be adjusted to the desired diameter by means of improvised means. However, the strength of this design will be questionable.

The diameter of vershinok can range from 1.8 to 4 mm. Very often, this parameter depends on the class of the rod and its manufacturer. So the fishing rods of the light and medium classes are usually equipped with vertices with a 2.3 mm bore. Fishing rods for long casting and construction, involving fishing in places with a strong current, are equipped with devices with a landing diameter of 2.6-3.6 mm. Picker rods are equipped with 1.8-2.2 mm products. But Extra Heavy Feeder class fishing rods most often have 4 mm tips.

Some manufacturers, such as Shimano, use dots with a 2.3 mm seat in almost all their rods and make them separately, making it much easier to replace these products.

Flow rings

A significant role in the selection of the product has the material and the diameter of the flow rings. The larger the rings will be, the easier it becomes to use the product. In large rings, litter is not clogged with fishing line, and the lightness and range of casting increases.

According to the material of the inner inserts, the rings are divided into:

  • Ceramic;
  • Silicon carbide products.

The advantage of rings with ceramic inserts in their cheapness. However, with frequent use, such items are quickly wiped. In this case, not only the insert, but also the carrying ring itself, becomes unusable.

Rings with inserts of silicon carbide can withstand prolonged and frequent use of even the most rigid braids. However, the material is very brittle, and if handled carelessly, the ring insert may crack.

Versions vershinok on manufacturing material

Tops for feeder rods are made of two types of material:

  • Fiberglass;
  • Carbon or carbon fiber.

Tops for feederAlso done done from composite materials. The core in them is made of fiberglass, wrapped with carbon fiber 2/3 of the length. Moreover, such structures have the advantages of both materials. Fiberglass tip is highly sensitive and reacts to even the slightest bite. Carbon while providing strength and rigidity of the product, allowing it to operate in conditions of strong current and wind. However, such done in extremely small quantities.

Fiberglass

Most of the fixtures are made from this material. Products differ in ease and hypersensibility. With proper use of the feeder, such a tip will react even to the slightest bit of a bite. At the same time, the detector is capable of withstanding various loads. All products from this material belong to the low and medium price segment.

Tops for feederThe disadvantage of the design of fiberglass is its excessive softness. The warning lamp is not suitable for fishing with wind and in water with a strong current. In addition, the material is subject to delamination and may be damaged under any load.

Carbon fiber

Material differs in ease and durability. After casting, the vershinka does not fluctuate in different directions. The carbon construction has a high sensitivity to biting, and even with strong winds or currents it reacts to even minor touches of the fish to the bait.

The disadvantage of such alarms is their high price. In addition, such products are usually equipped with rods related to the price segment above the average.

Criterias of choice

In order to choose the right vershinka for the feeder rod, the store should take a knee, which includes a warning device during installation. When fitting, it is important that the product fits tightly into the knee and during the backswing, as well as at rest, there is no backlash.

In the case when it was not possible to pick up the product clearly in size, it is worth buying an alarm device with a diameter that is minimally different from the required one, and modify it yourself. Too large a diameter can be reduced with fine-grained sandpaper. The missing millimeters are increased by winding on the butt of the braid, which must then be varnished.

Trying to do it yourself

In most cases, in the absence of a suitable tip for the feeder in diameter and stiffness, anglers acquire a warning device of a smaller or larger diameter and sensitivity, and subsequently finalize it with their own hands. However, it is possible to build a bite warning device from improvised means.

Pendulum device

To create the main part of the design, you can use plastic cocktail tubes with a grooved bending knee or counter feeder for the feeder. When using tubes, the holes overlap with foam.

Loops under the fishing line are installed at the ends of the tubes or counter-twist. Hinges can be made from ordinary paper clips. On a knee the carbine for installation of freight or a feeding trough fastens. If desired, it can be supplemented with a bell.

Nod-type product

Fastening the finished signaling device of this type can be made both in front, on the rod stand, and on the side, next to the handle. For the manufacture of such nods used flexible wire. It can be both a string from a piano, and a flexible steel strip from the antenna. On one side, 4 cm from the edge, the wire bends at an angle of 900. On the other hand, the wire is bent in the shape of a letter Z. Each bend should be about 1 cm.

Curved under 900 The side of the wire is applied to the rod between the first ring and the coil. It is possible to fix the nod either using scotch tape or using a special rubber band for metal nods for winter fishing rods. These rubber bands are equipped with 3 holes:

  • For fixing to the rod;
  • Under the nod;
  • For fishing line.

It is better to place a homemade nod 10-15 cm from the coil. Z-shaped hook fixed by a nod, for ease of use, painted in bright colors. To use it after each cast, the line must be tightened and put into a Z-shaped hook.

The second variant of the homemade nodding signaling device is the placement of a suitable flexible wire in the second leg. In this case, the first segment must be removed. Fixation is carried out using tape or tape. At the end of the wire set tulip. For ease of use, it can be marked with bright paint or fixed with red tape. This vertex, if necessary, successfully replaces the factory version. However, a significant drawback is the inability to fold it.

General recommendations for use

The top is always selected under the conditions of fishing and, most importantly, the net weight of the feeder. And the design of the feeder at the same time must meet the conditions of the reservoir and weather.

In the case when fishing will occur in still water, it is recommended to install a soft warning device. In windy weather on the lake, as well as for fishing on rivers with a weak current, it is better to use products of medium hardness. But rigid structures will be useful in the process of fishing for large fish, as well as in places of strong current and with significant wind.

The expected casting distance also plays a significant role in the process of operation. For fishing that does not involve long-distance casting of the lure, you can use soft and medium hardness detectors. But for long-distance fishing, a rigid structure is necessary.

Like this post? Please share to your friends:
Leave a Reply

;-) :| :x :twisted: :smile: :shock: :sad: :roll: :razz: :oops: :o :mrgreen: :lol: :idea: :grin: :evil: :cry: :cool: :arrow: :???: :?: :!: